ATV312HU15N4

Altivar 312

Variable speed drive

Asynchronous motors

Simple machine

With heat sink

ATV312

1.5 kW

2 hp

380...500 V - 15...10 %

50...60 Hz - 5...5 %

3 phases

6.4 A at 380 V, Isc = 5 kA
4.8 A at 500 V

Integrated

4.2 kVA

6.2 A for 60 s

61 W at nominal load

1…50

Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 5 mm² AWG 10

Internal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection

Modbus
CANopen

IP20 on upper part without cover plate
IP21 on connection terminals
IP31 on upper part
IP41 on upper part

Communication card for CANopen daisy chain
Communication card for DeviceNet
Communication card for Fipio
Communication card for Modbus TCP
Communication card for Profibus DP

323…550 V

47.5...63 Hz

5 kA

4.1 A at 4 kHz

0…500 kHz

4 kHz

2...16 kHz adjustable

170…200 % of nominal motor torque

150 % during 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor

Frequency PI regulator

Suppressable
Adjustable
Automatic whatever the load

<= power supply voltage

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6 N.m
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 1.2 N.m

Electrical between power and control

3

AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 Ohm
AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm
AI3 configurable current 0...20 mA, impedance: 250 Ohm

AI1, AI2, AI3: 8 ms analog
LI1...LI6: 4 ms discrete

AOV, AOC 8 ms for analog
R1A, R1B, R1C, R2A, R2B 8 ms for discrete

+/- 0.2 % for output

1

AOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bits
AOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits

Logic input not wired (LI1...LI4), < 13 V (state 1)
Negative logic (source) (LI1...LI6), > 19 V (state 0)
Positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1)

2

Configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic: (R2A, R2B) NC - 100000 cycles

R1-R2 10 mA at 5 V DC

R1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms
R1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms
R1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms
R1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms

6

(LI1...LI6) programmable at 24 V, 0…100 mA for PLC, impedance: 3500 Ohm

S, U or customized
Linear adjustable separately from 0.1 to 999.9 s

By DC injection

Input phase breaks: drive
Line supply overvoltage and undervoltage safety circuits: drive
Line supply phase loss safety function, for three phases supply: drive
Motor phase breaks: drive
Overcurrent between output phases and earth (on power up only): drive
Overheating protection: drive
Short-circuit between motor phases: drive
Thermal protection: motor

>= 500 mOhm 500 V DC for 1 minute

Drive voltage: 1 LED (red)
CANopen bus status: four 7-segment display units

5 ms for reference change

Analog input: 0.1...100 Hz
Display unit: 0.1 Hz

1 RJ45 for Modbus/CANopen

RS485 multidrop serial link

RTU

10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen
4800, 9600 or 19200 bps for Modbus

1…127 for CANopen
1…247 for Modbus

127 for CANopen
31 for Modbus

CE

Vertical +/- 10 degree

382 x 239 x 170 mm
143 x 105 x 150 mm
184 x 149 x 157 mm

143 mm

107 mm

152 mm

1.8 kg

2410 V DC between earth and power terminals
3400 V AC between control and power terminals

1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3

IEC 61800-3
IEC 61800-5-1

UL
DNV
CSA
C-Tick
NOM
GOST

2

TC

1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-6
1.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-6

15 gn for 11 ms conforming to EN/IEC 60068-2-27

5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3

-25…70 °C

-10…50 °C without (with protective cover on top of the drive)
-10…60 °C with derating factor (without protective cover on top of the drive)

<= 1000 m without
1000...3000 m with current derating 1 % per 100 m

12 months