variable speed drive ATV212 - 15kW - 20hp - 240V - 3 ph - wo EMC - IP21Show more characteristics >
Main range of productAltivar 212 product or component typeVariable speed drive device short nameATV212 product destinationAsynchronous motors product specific applicationPumps and fans in HVAC assembly styleWith heat sink network number of phases3 phases motor power kW15 kW motor power hp20 hp [Us] rated supply voltage200...240 V - 15...10 % supply voltage limits170…264 V supply frequency50...60 Hz - 5...5 % network frequency47.5...63 Hz EMC filterWithout EMC filter line current45.5 A at 240 V56.1 A at 200 V Complementary apparent power23.2 kVA at 240 V prospective line Isc22 kA continuous output current61 A at 230 V maximum transient current67.1 A for 60 s speed drive output frequency0.5…200 Hz nominal switching frequency12 kHz switching frequency6...16 kHz adjustable12...16 kHz with derating factor speed range1…10 speed accuracy+/- 10 % of nominal slip 0.2 Tn to Tn torque accuracy+/- 15 % transient overtorque120 % of nominal motor torque +/- 10 % for 60 s asynchronous motor control profileFlux vector control without sensor, standardVoltage/frequency ratio, 5 pointsVoltage/frequency ratio, automatic IR compensation (U/f + automatic Uo)Voltage/frequency ratio, 2 pointsVoltage/frequency ratio - Energy Saving, quadratic U/f regulation loopAdjustable PI regulator motor slip compensationAutomatic whatever the loadAdjustableNot available in voltage/frequency ratio motor control local signallingDC bus energized: 1 LED (red) output voltage<= power supply voltage isolationElectrical between power and control type of cableWithout mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPRWithout mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVCWith UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC electrical connectionVIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES: terminal 2.5 mm² / AWG 14L1/R, L2/S, L3/T: terminal 25 mm² / AWG 3 tightening torque0.6 N.m (VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES)4.5 N.m, 40 lb.in (L1/R, L2/S, L3/T) supplyInternal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 A, protection type: overload and short-circuit protectionInternal supply: 24 V DC (21…27 V), <200 A, protection type: overload and short-circuit protection analogue input number2 analogue input typeVIA switch-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bitsVIB configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bitsVIB configurable PTC probe: 0...6 probes, impedance: 1500 OhmVIA switch-configurable current: 0...20 mA, impedance: 250 Ohm, resolution 10 bits sampling duration2 ms +/- 0.5 ms F discrete2 ms +/- 0.5 ms R discrete2 ms +/- 0.5 ms RES discrete3.5 ms +/- 0.5 ms VIA analog22 ms +/- 0.5 ms VIB analog response timeFM 2 ms, tolerance +/- 0.5 ms for analog output(s)FLA, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)FLB, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)RY, RC 7 ms, tolerance +/- 0.5 ms for discrete output(s) accuracy+/- 0.6 % (VIA) for a temperature variation 60 °C+/- 0.6 % (VIB) for a temperature variation 60 °C+/- 1 % (FM) for a temperature variation 60 °C linearity errorVIA: +/- 0.15 % of maximum value for inputVIB: +/- 0.15 % of maximum value for inputFM: +/- 0.2 % for output analogue output number1 analogue output typeFM switch-configurable voltage 0...10 V DC, impedance: 7620 Ohm, resolution 10 bitsFM switch-configurable current 0...20 mA, impedance: 970 Ohm, resolution 10 bits discrete output number2 discrete output typeConfigurable relay logic: (FLA, FLC) NO - 100000 cyclesConfigurable relay logic: (FLB, FLC) NC - 100000 cyclesConfigurable relay logic: (RY, RC) NO - 100000 cycles minimum switching current3 mA at 24 V DC for configurable relay logic maximum switching current5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R)2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R) discrete input typeF programmable 24 V DC, with level 1 PLC, impedance: 4700 OhmR programmable 24 V DC, with level 1 PLC, impedance: 4700 OhmRES programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm discrete input logicPositive logic (source) (F, R, RES), <= 5 V (state 0), >= 11 V (state 1)Negative logic (sink) (F, R, RES), >= 16 V (state 0), <= 10 V (state 1) acceleration and deceleration rampsAutomatic based on the loadLinear adjustable separately from 0.01 to 3200 s braking to standstillBy DC injection protection typeOverheating protection: driveThermal power stage: driveShort-circuit between motor phases: driveInput phase breaks: driveOvercurrent between output phases and earth: driveOvervoltages on the DC bus: driveBreak on the control circuit: driveAgainst exceeding limit speed: driveLine supply overvoltage and undervoltage: driveLine supply undervoltage: driveAgainst input phase loss: driveThermal protection: motorMotor phase break: motorWith PTC probes: motor dielectric strength2830 V DC between earth and power terminals4230 V DC between control and power terminals insulation resistance>= 1 mOhm 500 V DC for 1 minute frequency resolutionDisplay unit: 0.1 HzAnalog input: 0.024/50 Hz communication port protocolAPOGEE FLNMETASYS N2ModbusLonWorksBACnet connector type1 RJ451 open style physical interface2-wire RS 485 transmission frameRTU transmission rate9600 bps or 19200 bps data format8 bits, 1 stop, odd even or no configurable parity type of polarizationNo impedance number of addresses1…247 communication serviceWrite multiple registers (16) 2 words maximumWrite single register (06)Read holding registers (03) 2 words maximumTime out setting from 0.1 to 100 sRead device identification (43)Monitoring inhibitable option cardCommunication card for LonWorks operating positionVertical +/- 10 degree width245 mm height330 mm depth190 mm net weight11.55 kg power dissipation in W629 W air flow215 m3/h specific applicationHVAC IP degree of protectionIP21 Motor power range AC-315…25 kW at 200…240 V 3 phases motor starter typeVariable speed drive Environment electromagnetic compatibilityElectrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-41.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 pollution degree2 conforming to IEC 61800-5-1 IP degree of protectionIP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529IP21 conforming to EN/IEC 61800-5-1IP21 conforming to EN/IEC 60529IP41 on upper part conforming to EN/IEC 61800-5-1IP41 on upper part conforming to EN/IEC 60529 vibration resistance1.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-61 gn (f= 13…200 Hz) conforming to EN/IEC 60068-2-8 shock resistance15 gn for 11 ms conforming to IEC 60068-2-27 environmental characteristicClasses 3C1 conforming to IEC 60721-3-3Classes 3S2 conforming to IEC 60721-3-3 noise level54 dB conforming to 86/188/EEC operating altitude1000...3000 m limited to 2000 m for the Corner Grounded distribution network with current derating 1 % per 100 m<= 1000 m without relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for operation-10…40 °C (without)40…50 °C (with derating factor) ambient air temperature for storage-25…70 °C standardsEN 61800-3 environments 1 category C2IEC 61800-3 environments 2 category C1IEC 61800-5-1EN 61800-3 environments 2 category C1EN 61800-5-1EN 61800-3 environments 1 category C1IEC 61800-3 environments 1 category C1IEC 61800-3 environments 2 category C3IEC 61800-3 environments 1 category C2EN 61800-3 environments 2 category C2EN 61800-3 environments 2 category C3IEC 61800-3 environments 2 category C2EN 61800-3 environments 1 category C3IEC 61800-3 environments 1 category C3UL Type 1EN 61800-3IEC 61800-3 product certificationsC-TickNOM 117CSAUL markingCE Offer Sustainability Sustainable offer statusGreen Premium product REACh Regulation EU RoHS DirectivePro-active compliance (Product out of EU RoHS legal scope)
EU RoHS Declaration
Mercury freeYes RoHS exemption information China RoHS Regulation Environmental Disclosure Circularity Profile WEEEThe product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins Contractual warranty Warranty18 months
Documents and DownloadsLanguage
DTM filesSizeAdd to My DocumentsCatalogueSizeAdd to My DocumentsUser guideSizeAdd to My DocumentsCADSizeAdd to My DocumentsCertificateSizeAdd to My DocumentsInstruction sheetSizeAdd to My DocumentsProduct Environmental ProfileSizeAdd to My Documents
No results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
Plate for EMC mounting (supplied with the drive)(1)2 x M5 screws
Mounting and ClearanceMounting RecommendationsClearance
Depending on the conditions in which the drive is to be used, its installation will require certain precautions and the use of appropriate accessories.
Install the unit vertically:
Do not place it close to heating elements.
Leave sufficient free space to ensure that the air required for cooling purposes can circulate from bottom to the top of the unit.
Type A mounting
Type B mounting
Type C mounting
By removing the protective blanking cover from the top of the drive, the degree of protection for the drive becomes IP21. The protective blanking cover may vary according to the drive model, see opposite.Specific Recommendations for Mounting in an Enclosure
To help ensure proper air circulation in the drive:
Sealed Metal Enclosure (IP54 Degree of Protection)
Fit ventilation grilles.
Check that there is sufficient ventilation. If there is not, install a forced ventilation unit with a filter. The openings and/or fans must provide a flow rate at least equal to that of the drive fans (refer to the product characteristics).
Use special filters with UL Type 12/IP54 protection.
Remove the blanking cover from the top of the drive.
The drive must be mounted in a dust and damp proof enclosure in certain environmental conditions, such as dust, corrosive gases, high humidity with risk of condensation and dripping water, splashing liquid, etc.This enables the drive to be used in an enclosure where the maximum internal temperature reaches 50°C.
Connections and SchemaRecommended Wiring Diagram3-Phase Power SupplyA1:ATV 212 driveKM1:ContactorQ1:Circuit breakerQ2:GV2 L rated at twice the nominal primary current of T1Q3:GB2CB05S1, S2:XB4 B or XB5 A pushbuttonsT1:100 VA transformer 220 V secondary(1)Fault relay contacts for remote signalling of the drive status(2)Connection of the common for the logic inputs depends on the positioning of the switch (Source, PLC, Sink)(3)Reference potentiometer SZ1RV1202
NOTE: All terminals are located at the bottom of the drive. Install interference suppressors on all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent lighting, etc.Switches (Factory Settings)
Voltage/current selection for analog I/O (VIA and VIB)
Voltage/current selection for analog I/O (FM)
Selection of logic type(1)negative logic(2)positive logicOther Possible Wiring DiagramsLogic Inputs According to the Position of the Logic Type Switch
“PLC” position with PLC transistor outputs(1)PLC(1)PLC
2-wire controlF:ForwardR:Preset speed(2)ATV 212 control terminals
3-wire controlF:ForwardR:StopRES:Reverse(2)ATV 212 control terminals
PTC probe(2)ATV 212 control terminals(3)MotorAnalog Inputs
Voltage analog inputs
External +10 V(2)ATV 212 control terminals(4)Speed reference potentiometer 2.2 to 10 kΩ(2)ATV 212 control terminals
Analog input configured for current: 0-20 mA, 4-20 mA, X-Y mA(2)ATV 212 control terminals(5)Source 0-20 mA, 4-20 mA, X-Y mA
Analog input VIA configured as positive logic input (“Source” position)(2)ATV 212 control terminals
Analog input VIA configured as negative logic input (“Sink” position)(2)ATV 212 control terminals
Performance CurvesDerating Curves
The derating curves for the drive nominal current (In) depend on the temperature, the switching frequency and the mounting type (A, B or C).
For intermediate temperatures (45°C for example), interpolate between 2 curves.XSwitching frequency