Main range of productHarmony XB5 product or component typeHead product destinationEmergency stop push-button device short nameZB5 bezel materialPlastic mounting diameter22 mm sale per indivisible quantity1 shape of signaling unit headRound type of operatormechanical latching resetKey release operator profileRed mushroom Ø 30 mm, unmarked type of keylockSpecial key key withdrawal positionCenter Complementary CAD overall width30 mm CAD overall height30 mm CAD overall depth79 mm net weight0.04 kg mechanical durability300000 cycles station nameXALD 1...5 cut-outsXALK 1...5 cut-outs electrical composition codeC7 for <4 contacts using single blocks in front mountingC8 for <4 contacts using single and double blocks in front mountingC11 for <3 contacts using single blocks in front mountingC15 for <1 contacts using single blocks in front mountingSF1 for <3 contacts using single blocks in front mountingSR1 for <3 contacts using single blocks in rear mountingC10 for <4 contacts using single and double blocks in front mounting Environment protective treatmentTH ambient air temperature for storage-40…70 °C ambient air temperature for operation-25…70 °C overvoltage categoryClass II conforming to IEC 60536 IP degree of protectionIP66 conforming to IEC 60529 NEMA degree of protectionNEMA 13NEMA 4X resistance to high pressure washer7000000 Pa at 55 °C, distance : 0.1 m IK degree of protectionIK03 conforming to IEC 50102 standardsEN/IEC 60947-5-1CSA C22.2 No 14EN/IEC 60947-5-4GB 14048.5EN/IEC 60947-5-5UL 508IEC 60364-5-53JIS C8201-5-1EN/IEC 60947-1JIS C8201-1 product certificationsBVCSARINALROS (Lloyds register of shipping)UL listedDNVGL vibration resistance5 gn (f= 2…500 Hz) conforming to IEC 60068-2-6 shock resistance30 gn (duration = 18 ms) for half sine wave acceleration conforming to IEC 60068-2-2750 gn (duration = 11 ms) for half sine wave acceleration conforming to IEC 60068-2-27 Contractual warranty Warranty18 months
Documents & DownloadsLanguage
Instruction sheetSizeAdd to My DocumentsZB4..., ZB5... Mounting XB4 pushbuttons chromium plated metal bezel and XB5 plastic bezel with or without circular yellow legends ZBY9.2., Instruction Sheet (Version 12)
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
Mounting and ClearancePanel Cut-out for Pushbuttons, Switches and Pilot Lights (Finished Holes, Ready for Installation)Connection by Screw Clamp Terminals or Plug-in Connectors or on Printed Circuit Board(1)Diameter on finished panel or support(2)For selector switches and Emergency stop buttons, use of an anti-rotation plate type ZB5AZ902 is recommended.(3)Ø22.5 mm recommended (Ø22.3 0+0.4) / Ø0.89 in. recommended (Ø0.88 in. 0+0.016)
a in mm
a in in.
b in mm
b in in.
By screw clamp terminals or plug-in connector
By Faston connectors
On printed circuit board
1.18Detail of Lug Recess(1)Diameter on finished panel or support(2)For selector switches and Emergency stop buttons, use of an anti-rotation plate type ZB5AZ902 is recommended.(3)Ø22.5 mm recommended (Ø22.3 0+0.4) / Ø0.89 in. recommended (Ø0.88 in. 0+0.016)Pushbuttons, Switches and Pilot Lights for Printed Circuit Board ConnectionPanel Cut-outs (Viewed from Installer’s Side)A:30 mm min. / 1.18 in. min.B:40 mm min. / 1.57 in. min.Printed Circuit Board Cut-outs (Viewed from Electrical Block Side)
Dimensions in mmA:30 mm min.B:40 mm min.
Dimensions in in.A:1.18 in. min.B:1.57 in. min.General Tolerances of the Panel and Printed Circuit Board
The cumulative tolerance must not exceed 0.3 mm / 0.012 in.: T1 + T2 = 0.3 mm max.Installation Precautions
Minimum thickness of circuit board: 1.6 mm / 0.06 in.
Cut-out diameter: 22.4 mm ± 0.1 / 0.88 in. ± 0.004
Orientation of body/fixing collar ZB5AZ009: ± 2°30’ (excluding cut-outs marked a and b).
Tightening torque of screws ZBZ006: 0.6 N.m (5.3 lbf.in) max.
Allow for one ZB5AZ079 fixing collar/pillar and its fixing screws:
every 90 mm / 3.54 in. horizontally (X), and 120 mm / 4.72 in. vertically (Y).
with each selector switch head (ZB5AD•, ZB5AJ•, ZB5AG•).
The fixing centers marked a and b are diagonally opposed and must align with those marked 4 and 5.(1)Head ZB5AD•(2)Panel(2)Nut(4)Printed circuit boardMounting of Adapter (Socket) ZBZ01•
1 2 elongated holes for ZBZ006 screw access
2 1 hole Ø 2.4 mm ± 0.05 / 0.09 in. ± 0.002 for centring adapter ZBZ01•
3 8 × Ø 1.2 mm / 0.05 in. holes
4 1 hole Ø 2.9 mm ± 0.05 / 0.11 in. ± 0.002, for aligning the printed circuit board (with cut-out marked a)
5 1 elongated hole for aligning the printed circuit board (with cut-out marked b)
6 4 holes Ø 2.4 mm / 0.09 in. for clipping in adapter ZBZ01•
Dimensions An + 18.1 relate to the Ø 2.4 mm ± 0.05 / 0.09 in. ± 0.002 holes for centring adapter ZBZ01•.
Technical DescriptionElectrical Composition Corresponding to Code C7Electrical Compositions Corresponding to Code C8Electrical Compositions Corresponding to Code C10Electrical Composition Corresponding to Codes C9, C11, SF1 and SR1Electrical Composition Corresponding to Code C15
1 N/O + N/C or 1 N/O + N/O or 1 N/C + N/CLegend