Main range of productAltivar 12 product or component typeVariable speed drive product destinationAsynchronous motors product specific applicationSimple machine assembly styleOn base plate component nameATV12 quantity per setSet of 1 EMC filterWithout EMC filter built-in fanWithout network number of phases3 phases [Us] rated supply voltage200...240 V - 15...10 % motor power kW0.18 kW motor power hp0.25 hp communication port protocolModbus line current2 A at 200 V1.7 A at 240 V speed range1…20 transient overtorque150…170 % of nominal motor torque depending on drive rating and type of motor asynchronous motor control profileSensorless flux vector controlVoltage/frequency ratio (V/f)Quadratic voltage/frequency ratio IP degree of protectionIP20 without blanking plate on upper part noise level0 dB Complementary supply frequency50/60 Hz +/- 5 % connector type1 RJ45 (on front face) for Modbus physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus transmission rate4800 bit/s9600 bit/s19200 bit/s38400 bit/s number of addresses1…247 for Modbus communication serviceRead holding registers (03) 29 wordsWrite single register (06) 29 wordsWrite multiple registers (16) 27 wordsRead/write multiple registers (23) 4/4 wordsRead device identification (43) prospective line Isc5 kA continuous output current1.4 A at 4 kHz maximum transient current2.1 A for 60 s speed drive output frequency0.5…400 Hz nominal switching frequency4 kHz switching frequency2...16 kHz adjustable4...16 kHz with derating factor braking torqueUp to 70 % of nominal motor torque without braking resistor motor slip compensationAdjustablePreset in factory output voltage200...240 V 3 phases electrical connectionTerminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC) tightening torque0.8 N.m insulationElectrical between power and control supplyInternal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protectionInternal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection analogue input number1 analogue input typeConfigurable current AI1 0...20 mA 250 OhmConfigurable voltage AI1 0...10 V 30 kOhmConfigurable voltage AI1 0...5 V 30 kOhm discrete input number4 discrete input typeProgrammable LI1...LI4 24 V 18...30 V discrete input logicNegative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhmPositive logic (source), 0...< 5 V (state 0), > 11 V (state 1) sampling duration20 ms, tolerance +/- 1 ms for logic input10 ms for analogue input linearity error+/- 0.3 % of maximum value for analogue input analogue output number1 analogue output typeAO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bitsAO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits discrete output number2 discrete output typeLogic output LO+, LO-Protected relay output R1A, R1B, R1C 1 C/O minimum switching current5 mA at 24 V DC for logic relay maximum switching current2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay acceleration and deceleration rampsULinear from 0 to 999.9 sS braking to standstillBy DC injection, <30 s protection typeLine supply overvoltageLine supply undervoltageOvercurrent between output phases and earthOverheating protectionShort-circuit between motor phasesAgainst input phase loss in three-phaseThermal motor protection via the drive by continuous calculation of I²t frequency resolutionAnalog input: converter A/D, 10 bitsDisplay unit: 0.1 Hz time constant20 ms +/- 1 ms for reference change markingCE operating positionVertical +/- 10 degree height143 mm width72 mm depth102.2 mm net weight0.7 kg specific applicationCommercial equipment motor starter typeVariable speed drive Environment electromagnetic compatibilityElectrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3Surge immunity test level 3 conforming to EN/IEC 61000-4-5Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11 electromagnetic emissionRadiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cableConducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 mConducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m product certificationsC-TickNOMGOSTULCSA vibration resistance1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-61.5 mm peak to peak (f = 3…13 Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/IEC 60068-2-6 shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27 relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for storage-25…70 °C ambient air temperature for operation-10…40 °C protective cover from the top of the drive removed40…60 °C with current derating 2.2 % per °C operating altitude<= 1000 m without> 1000...3000 m with current derating 1 % per 100 m Offer Sustainability Sustainable offer statusGreen Premium product REACh Regulation EU RoHS DirectivePro-active compliance (Product out of EU RoHS legal scope)
EU RoHS Declaration
Mercury freeYes RoHS exemption information China RoHS Regulation Environmental Disclosure Circularity Profile WEEEThe product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins Contractual warranty Warranty18 months
Documents and DownloadsLanguage
CatalogueSizeAdd to My DocumentsUser guideSizeAdd to My DocumentsCADSizeAdd to My DocumentsCertificateSizeAdd to My DocumentsInstruction sheetSizeAdd to My DocumentsEnd of Life InformationSizeAdd to My Documents
No results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.