View all Altivar 212
Main range of productAltivar 212 product or component typeVariable speed drive device short nameATV212 product destinationAsynchronous motors product specific applicationPumps and fans in HVAC assembly styleWith heat sink network number of phases3 phases motor power kW18.5 kW motor power hp25 hp [Us] rated supply voltage380...480 V - 15...10 % supply voltage limits323…528 V supply frequency50...60 Hz - 5...5 % network frequency47.5...63 Hz EMC filterClass C2 EMC filter integrated line current27.8 A at 480 V34.8 A at 380 V Complementary apparent power28.2 kVA at 380 V prospective line Isc22 kA continuous output current37 A at 380 V37 A at 460 V maximum transient current40.7 A for 60 s speed drive output frequency0.5…200 Hz nominal switching frequency8 kHz switching frequency6...16 kHz adjustable8...16 kHz with derating factor speed range1…10 speed accuracy+/- 10 % of nominal slip 0.2 Tn to Tn torque accuracy+/- 15 % transient overtorque120 % of nominal motor torque +/- 10 % for 60 s asynchronous motor control profileVoltage/frequency ratio, 5 pointsVoltage/frequency ratio - Energy Saving, quadratic U/fVoltage/frequency ratio, 2 pointsVoltage/frequency ratio, automatic IR compensation (U/f + automatic Uo)Flux vector control without sensor, standard regulation loopAdjustable PI regulator motor slip compensationNot available in voltage/frequency ratio motor controlAutomatic whatever the loadAdjustable local signalling1 LED (red)DC bus energized: output voltage<= power supply voltage isolationElectrical between power and control type of cableWithout mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPRWithout mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVCWith UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC electrical connectionVIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES: terminal 2.5 mm² / AWG 14L1/R, L2/S, L3/T: terminal 25 mm² / AWG 3 tightening torque0.6 N.m (VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES)4.5 N.m, 40 lb.in (L1/R, L2/S, L3/T) supplyInternal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 A, protection type: overload and short-circuit protectionInternal supply: 24 V DC (21…27 V), <200 A, protection type: overload and short-circuit protection analogue input number2 analogue input typeVIA switch-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bitsVIB configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bitsVIB configurable PTC probe: 0...6 probes, impedance: 1500 OhmVIA switch-configurable current: 0...20 mA, impedance: 250 Ohm, resolution 10 bits sampling duration2 ms +/- 0.5 ms F discrete2 ms +/- 0.5 ms R discrete2 ms +/- 0.5 ms RES discrete3.5 ms +/- 0.5 ms VIA analog22 ms +/- 0.5 ms VIB analog response timeFM 2 ms, tolerance +/- 0.5 ms for analog output(s)FLA, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)FLB, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)RY, RC 7 ms, tolerance +/- 0.5 ms for discrete output(s) accuracy+/- 0.6 % (VIA) for a temperature variation 60 °C+/- 0.6 % (VIB) for a temperature variation 60 °C+/- 1 % (FM) for a temperature variation 60 °C linearity errorVIA: +/- 0.15 % of maximum value for inputVIB: +/- 0.15 % of maximum value for inputFM: +/- 0.2 % for output analogue output number1 analogue output typeFM switch-configurable voltage 0...10 V DC, impedance: 7620 Ohm, resolution 10 bitsFM switch-configurable current 0...20 mA, impedance: 970 Ohm, resolution 10 bits discrete output number2 discrete output typeConfigurable relay logic: (FLA, FLC) NO - 100000 cyclesConfigurable relay logic: (FLB, FLC) NC - 100000 cyclesConfigurable relay logic: (RY, RC) NO - 100000 cycles minimum switching current3 mA at 24 V DC for configurable relay logic maximum switching current5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R)2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R) discrete input typeF programmable 24 V DC, with level 1 PLC, impedance: 4700 OhmR programmable 24 V DC, with level 1 PLC, impedance: 4700 OhmRES programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm discrete input logicPositive logic (source) (F, R, RES), <= 5 V (state 0), >= 11 V (state 1)Negative logic (sink) (F, R, RES), >= 16 V (state 0), <= 10 V (state 1) acceleration and deceleration rampsLinear adjustable separately from 0.01 to 3200 sAutomatic based on the load braking to standstillBy DC injection protection typeOverheating protection: driveThermal power stage: driveShort-circuit between motor phases: driveInput phase breaks: driveOvercurrent between output phases and earth: driveOvervoltages on the DC bus: driveBreak on the control circuit: driveAgainst exceeding limit speed: driveLine supply overvoltage and undervoltage: driveLine supply undervoltage: driveAgainst input phase loss: driveThermal protection: motorMotor phase break: motorWith PTC probes: motor dielectric strength3535 V DC between earth and power terminals5092 V DC between control and power terminals insulation resistance>= 1 mOhm 500 V DC for 1 minute frequency resolutionDisplay unit: 0.1 HzAnalog input: 0.024/50 Hz communication port protocolAPOGEE FLNBACnetLonWorksModbusMETASYS N2 connector type1 open style1 RJ45 physical interface2-wire RS 485 transmission frameRTU transmission rate9600 bps or 19200 bps data format8 bits, 1 stop, odd even or no configurable parity type of polarizationNo impedance number of addresses1…247 communication serviceTime out setting from 0.1 to 100 sRead device identification (43)Monitoring inhibitableRead holding registers (03) 2 words maximumWrite multiple registers (16) 2 words maximumWrite single register (06) option cardCommunication card for LonWorks operating positionVertical +/- 10 degree width245 mm height330 mm depth190 mm net weight11.65 kg power dissipation in W603 W air flow214 m3/h functionalityMid specific applicationHVAC IP degree of protectionIP21 Motor power range AC-315…25 kW at 380…440 V 3 phases15…25 kW at 480…500 V 3 phases motor starter typeVariable speed drive Environment electromagnetic compatibilityElectrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-41.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 pollution degree2 conforming to IEC 61800-5-1 IP degree of protectionIP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529IP21 conforming to EN/IEC 61800-5-1IP21 conforming to EN/IEC 60529IP41 on upper part conforming to EN/IEC 61800-5-1IP41 on upper part conforming to EN/IEC 60529 vibration resistance1.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-61 gn (f= 13…200 Hz) conforming to EN/IEC 60068-2-8 shock resistance15 gn for 11 ms conforming to IEC 60068-2-27 environmental characteristicClasses 3C1 conforming to IEC 60721-3-3Classes 3S2 conforming to IEC 60721-3-3 noise level54 dB conforming to 86/188/EEC operating altitude1000...3000 m limited to 2000 m for the Corner Grounded distribution network with current derating 1 % per 100 m<= 1000 m without relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for operation-10…40 °C (without)40…50 °C (with derating factor) ambient air temperature for storage-25…70 °C standardsEN 61800-3 environments 1 category C2EN 61800-3 category C2IEC 61800-3IEC 61800-3 environments 1 category C1IEC 61800-5-1IEC 61800-3 environments 2 category C1IEC 61800-3 environments 2 category C2IEC 61800-3 environments 1 category C2EN 55011 class A group 1EN 61800-3 environments 1 category C3IEC 61800-3 environments 1 category C3EN 61800-3IEC 61800-3 category C3EN 61800-3 category C3IEC 61800-3 category C2EN 61800-5-1UL Type 1IEC 61800-3 environments 2 category C3EN 61800-3 environments 1 category C1EN 61800-3 environments 2 category C2EN 61800-3 environments 2 category C3EN 61800-3 environments 2 category C1 product certificationsCSAULC-TickNOM 117 markingCE Offer Sustainability Sustainable offer statusGreen Premium product REACh Regulation EU RoHS DirectivePro-active compliance (Product out of EU RoHS legal scope)
EU RoHS Declaration
Mercury freeYes RoHS exemption information China RoHS Regulation Environmental Disclosure Circularity Profile WEEEThe product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins Contractual warranty Warranty18 months
Documents and DownloadsLanguage
CatalogueSizeAdd to My DocumentsUser guideSizeAdd to My DocumentsInstruction sheetSizeAdd to My DocumentsCADSizeAdd to My DocumentsCertificateSizeAdd to My DocumentsDTM filesSizeAdd to My DocumentsProduct Environmental ProfileSizeAdd to My Documents
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.