CatalogLanguageFormatSizeDateEnglishprp.document.label.format pdfSize 5.2 MBDate 6/14/19DescriptionTable of Contents: Introduction, Basic Energy Metering (IEM3000 series), Basic multi-function metering (PM3000, PM5000, ION6200, EM3500, and EM4200 series), Intermediate Metering (PM8000 series), Advanced metering (ION7550, ION7650 series, CM4000T, ION9000 series), Advanced utility metering (ION7550, ION8650 series), Multi-circuit metering (BCPM, EM4900, EM4000, and EM4800), Communications (Link150, Com'X 210, Com'X 510, and ION7550 RTU), and Monitoring software EcoStruxure power management softwareUser guideLanguageFormatSizeDateEnglishprp.document.label.format pdfSize 112.4 KBDate 9/1/19DescriptionThis technical note outlines the compliance of applicable PowerLogic meters with the International Electrotechnical Commission’s IEC 61000-4-30 (or “4-30”) standard, and is intended for personnelwith knowledge of power quality and power quality standards.Englishprp.document.label.format pdfSize 187.7 KBDate 7/1/16DescriptionFirmware version v1.3.1 for the ION7400 series meter adds Internal clock temperature compensation feature and resolves previously unknown Modbus master issue. This document also contains IPv6 global addressing and IPv6 gateway support content from the previous what's new document (7EN12-0296).
Software - ReleasedLanguageFormatSizeDateEnglishprp.document.label.format zipSize 1.9 MBDate 7/27/16DescriptionPlease find in the attached .zip file OfflineMeter executables for the ION7400. Offline Meters, or meter simulators, are used on your Windows PC to emulate the meter hardware platform for the development and testing of meter application logic (a.k.a ION frameworks) using either ION Setup software or ION Enterprise Designer. Once the meter simulator is running, it can be accessed at the domain name "localhost" (127.0.0.1) with software on the same computer.FirmwareLanguageFormatSizeDateEnglishprp.document.label.format zipSize 17.8 MBDate 11/20/19Files in documentzip16.7 MB942.2 KB161.9 KBDescriptionThis ZIP file contains the files to upgrade the PowerLogic™ ION7400 series meter to firmware v2.2.1 (V002.002.001), Meter Template, Modbus Map document, SNMP MIB, Webpages, What’s new document and other associated files. See the Upgrading Meter Firmware to v2.2.1 document for important information on performing this upgrade. Verify the checksum of the file to help ensure it was not corrupted during download using the SHA-256 File Signature for the ION9000_V002.002.001.zip file: 24d17cab3359d03cddc4ff3fdb0ee84b9a85022dfb24cb1ba9e30ecc6e4e5956. NOTE: To apply this firmware, the meter must have firmware v2.1.0. Go to schneider-electric.com and search for Upgrade devices to firmware v 2.1.0 and follow instructions on how to get and apply firmware v2.1.0.Englishprp.document.label.format zipSize 16.8 MBDate 4/30/19Files in documentDescriptionFirmware version 2.1.0 for the PowerLogic™ ION7400 MID series meter adds enhanced firmware upgrade support, PTP, Secure HTTPS webserver, ION Module updates, updated support for the latest versions of EN50160, IEEE 519 and IEC 61000-4-30 power quality standards, pre- and post-event data capture for data and waveform recorders, and 0-20 mA support for the Analog I/O option module.To upgrade your meter to firmware version 2.1.0, you must use ION Setup version 3.1 or later. Please refer to the “Upgrading devices to firmware v2.1.0” technical note at https://www.se.com/ww/en/download/document/7EN72-0203/ for instructions on upgrading your meter firmware to version 2.1.0.SHA256 File signatures:f90c29967e1b94c3f4783c1524d03b01ed9418f0f71614bb65fec08848a1d224 *ION7400_MID_V002.001.000.zipEnglishprp.document.label.format zipSize 28.6 MBDate 3/4/19Files in document166.7 KB286 KBzip28.1 MBDescriptionFirmware version 2.1.0 for the PowerLogic™ ION7400 series meter adds enhanced firmware upgrade support, PTP, Secure HTTPS webserver, ION Module updates, updated support for the latest versions of EN50160, IEEE 519 and IEC 61000-4-30 power quality standards, pre- and post-event data capture for data and waveform recorders, and 0-20 mA support for the Analog I/O option module.To upgrade your meter to firmware version 2.1.0, you must use ION Setup version 3.1 or later. Please refer to the “Upgrading devices to firmware v2.1.0” technical note at https://www.se.com/ww/en/download/document/7EN72-0203/ for instructions on upgrading your meter firmware to version 2.1.0.SHA256 File signatures:5f95a642a2c6401f38155e9984f3f1c11169ae9f0d8f6b9874246f180d205ba9 *ION7400_V002.001.000.zipEnglishprp.document.label.format zipSize 23.2 MBDate 2/16/18Englishprp.document.label.format zipSize 23.1 MBDate 2/16/18Files in documentdcf1,013.4 KBzip221.2 KBexe9.1 MBupg12.1 MBzip790.9 KBmib19.9 KBDescriptionFirmware version v1.4.3 for the PowerLogic™ ION7400 series meter includes the following features or feature enhancements: Modbus product ID - Security Enhancements - Extended logging capability beyond the current 10MB limit. - Waveform Viewer on Webpage - DHCP over IPv4 and IPv6 - High Speed Relative Setpoints - DLMS protocol support – NERC CIP ready and MID compliance.ION7400_MID_V001.004.003.upg SHA-256:c56cc7776efd6bc8504030fb51982579c780b73b18c7512e69994819d19a0dd8Englishprp.document.label.format zipSize 7.3 MBDate 8/19/16DescriptionFirmware version v1.3.1 for the PowerLogic™ION7400 series meter adds a new feature that provides automatic temperature compensation for your meter’s internal clock. This firmware also resolves a previously unknown issue with firmware version v1.3.0. Features added from the previous firmware version include IPv6 global addressing and IPv6 gateway support.