ATV12P037F1

Altivar 12

Variable speed drive

Asynchronous motors

Simple machine

On base plate

ATV12

Set of 1

Without EMC filter

Without

1 phase

100...120 V - 15...10 %

0.37 kW

0.55 hp

Modbus

11.4 A at 100 V
9.3 A at 120 V

1…20

150…170 % of nominal motor torque depending on drive rating and type of motor

Quadratic voltage/frequency ratio
Voltage/frequency ratio (V/f)
Sensorless flux vector control

IP20 without blanking plate on upper part

0 dB

50/60 Hz +/- 5 %

1 RJ45 (on front face) for Modbus

2-wire RS 485 for Modbus

RTU for Modbus

4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s

1…247 for Modbus

Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)

1 kA

2.4 A at 4 kHz

3.6 A for 60 s

0.5…400 Hz

4 kHz

2...16 kHz adjustable
4...16 kHz with derating factor

Up to 70 % of nominal motor torque without braking resistor

Adjustable
Preset in factory

200...240 V 3 phases

Terminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC)

0.8 N.m

Electrical between power and control

Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection
Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection

1

Configurable current AI1 0...20 mA 250 Ohm
Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm

4

Programmable LI1...LI4 24 V 18...30 V

Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)

20 ms, tolerance +/- 1 ms for logic input
10 ms for analogue input

+/- 0.3 % of maximum value for analogue input

1

AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits

2

Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O

5 mA at 24 V DC for logic relay

2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay

S
Linear from 0 to 999.9 s
U

By DC injection, <30 s

Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t

Analog input: converter A/D, 10 bits
Display unit: 0.1 Hz

20 ms +/- 1 ms for reference change

CE

Vertical +/- 10 degree

143 mm

72 mm

102.2 mm

0.7 kg

Mixer Commercial equipment
Other application Commercial equipment
Ironing Textile

Variable speed drive

Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2
Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3
Surge immunity test level 3 conforming to EN/IEC 61000-4-5
Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11

Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cable
Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <5 m
Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m
Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m

NOM
UL
C-Tick
CSA
GOST

1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f = 3…13 Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/IEC 60068-2-6

15 gn conforming to EN/IEC 60068-2-27 for 11 ms

5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3

-25…70 °C

-10…40 °C protective cover from the top of the drive removed
40…60 °C with current derating 2.2 % per °C

> 1000...2000 m with current derating 1 % per 100 m
<= 1000 m without

Green Premium product

REACh Declaration

Pro-active compliance (Product out of EU RoHS legal scope)
EU RoHS Declaration

Yes

Yes

China RoHS declaration

Product Environmental Profile

End of Life Information

The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins

18 months