Main range of productAltivar 61 Plus product or component typeVariable speed drive device short nameATV61 product destinationSynchronous motorsAsynchronous motors product specific applicationPumping and ventilation machine assembly styleIn floor-standing enclosure with separate air flows product compositionA plinthA switch and fast-acting fusesIntegrated drive system ATV61EM12YE1An IP65 remote mounting kit for graphic display terminalTerminals/bars for motor connectionA wired ready-assembled Sarel Spacial 6000 enclosureControl transformer for 230 V EMC filterIntegrated network number of phases3 phases rated supply voltage500...525 V +/- 10 % supply frequency50...60 Hz motor power kW900 kW, 3 phases at 500...525 V line current1212 A at 500 V3 phases / 900 kW IP degree of protectionIP23 Complementary apparent power1050 kVA for 500 V3 phases / 900 kW prospective line Isc100 kA with external fuses continuous output current1230 A at 2.5 kHz, 500 V3 phases maximum transient current1476 A for 60 s 3 phases speed drive output frequency0.1…500 Hz nominal switching frequency2.5 kHz switching frequency2...4.9 kHz adjustable2.5...4.9 kHz with derating factor speed range1…100 in open-loop mode, without speed feedback speed accuracy+/- 10 % of nominal slip 0.2 Tn to Tn without speed feedback torque accuracy+/- 15 % in open-loop mode, without speed feedback transient overtorque120 % of nominal motor torque for 60 s135 % of nominal motor torque for 2 s braking torque30 % without braking resistor<= 125 % with braking resistor asynchronous motor control profileVoltage/frequency ratio, 5 pointsVoltage/frequency ratio - Energy Saving, quadratic U/fFlux vector control without sensor, standardVoltage/frequency ratio, 2 points synchronous motor control profileVector control without sensor, standard regulation loopAdjustable PI regulator motor slip compensationAdjustableSuppressableAutomatic whatever the loadNot available in voltage/frequency ratio (2 or 5 points) supply voltage limits450…578 V network frequency limits47.5…63 Hz overvoltage categoryClass 3 conforming to EN 50178 local signallingLCD display unitoperation function, status and configuration: output voltage<= supply voltage isolationElectrical between power and control type of cable for external connectionIEC cable at 40 °C, copper 70 °C / PVC electrical connectionBar M12 - 16 x 240 mm² 41 N.m (U/T1, V/T2, W/T3) entry from the bottomTerminal - 2.5 mm² / AWG 14 0.6 N.m (R1A, R1B, R1C, R2A, R2B) entry from the bottomScrew clamp terminals - 1.5 mm² 0.25 N.m (AI1-/AI1+, AI2, AO1, LI1...LI6, PWR) entry from the bottomBar M12 - 10 x 240 mm² 41 N.m (L1/R, L2/S, L3/T) entry from the bottom at 6-pulse operationBar M12 - 4 x 240 mm² 41 N.m (L1/R, L2/S, L3/T) entry from the bottom at 12-pulse operation motor recommanded cable cross section5 (3 x 240) mm²6 (3 x 185) mm² short-circuit protection1600 A fuse protection type gI - power supply upstream - at 6-pulse operation800 A fuse protection type gI - power supply upstream - at 12-pulse operation supplyExternal supply: 24 V (19…30 V)DC, <1 AInternal supply for reference potentiometer: 10 V (10…11 V)DC, <10 AInternal supply: 24 V (21…27 V)DC, <100 A analogue input number2 analogue input typeAI2 software-configurable voltage: 0...10 V DC, 24 V max, impedance: 30 kOhm, sampling time: 1.5…2.5 ms, resolution: 11 bitsAI1-/Al1+ bipolar differential voltage: +/- 10 V DC, 24 V max, sampling time: 1.5…2.5 ms, resolution: 11 bits + signAI2 software-configurable current: 0...20 mA/4...20 mA, impedance: 250 Ohm, sampling time: 1.5…2.5 ms, resolution: 11 bits analogue output number1 analogue output typeSoftware-configurable voltage: (AO1) 0...10 V DC - 500 Ohm - sampling time: 1.5…2.5 ms - resolution: 10 bitsSoftware-configurable current: (AO1) 0...20 mA/4...20 mA - 500 Ohm - sampling time: 1.5…2.5 ms - resolution: 10 bits discrete output number2 discrete output typeConfigurable relay logic: (R1A, R1B, R1C)NO/NC - 6.5...7.5 ms - 100000 cyclesConfigurable relay logic: (R2A, R2B)NO - 6.5...7.5 ms - 100000 cycles minimum switching current3 mA at 24 V DC (configurable relay logic) maximum switching current5 A at 250 V AC on resistive load - cos phi = 1 for configurable relay logic5 A at 30 V DC on inductive load - L/R = 7 ms for configurable relay logic5 A at 30 V DC on resistive load - L/R = 0 ms for configurable relay logic5 A at 250 V AC on inductive load - cos phi = 0.4 for configurable relay logic discrete input number7 discrete input typeProgrammable (LI1...LI5) at 24 V DC <= 30 V level 1 PLC 3.5 kOhm (duration=1.5…2.5 ms)Switch-configurable (LI6) at 24 V DC <= 30 V level 1 PLC 1.5 kOhm (duration=1.5…2.5 ms)Safety input (PWR) at 24 V DC <= 30 V 1.5 kOhm discrete input logicPositive (LI1...LI6), 0...5 V (state 0), 11...30 V (state 1)Negative (LI1...LI6), 16...30 V (state 0), 0...10 V (state 1)Positive (PWR), 0...2 V (state 0), 17...30 V (state 1) acceleration and deceleration rampsLinear adjustable separately from 0.01 to 9000 sS, U or customized braking to standstillBy DC injection, <60 s protection typeOverheating protection: driveThermal protection: driveShort-circuit between motor phases: driveInput phase breaks: driveOvercurrent between output phases and earth: driveOvervoltages on the DC bus: driveBreak on the control circuit: driveAgainst exceeding limit speed: driveLine supply undervoltage: driveLine supply overvoltage: driveAgainst input phase loss: driveThermal protection: motorMotor phase break: motorPower removal: drivePower removal: motor dielectric strength3535 V DC between earth and power terminals5092 V DC between control and power terminals insulation resistance> 1 mOhm 500 V DC for 1 minute frequency resolutionDisplay unit: 0.1 HzAnalog input: 0.024/50 Hz communication port protocolCANopenModbus connector type1 RJ45 (on front face) for Modbus1 RJ45 (on terminal) for ModbusMale SUB-D 9 on RJ45 for CANopen physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus transmission rate9600 bps, 19200 bps for Modbus on front face4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen data format8 bits, 1 stop, even parity for Modbus on front face8 bits, odd even or no configurable parity for Modbus on terminal type of polarizationNo impedance for Modbus number of addresses1…247 for Modbus1…127 for CANopen method of accessSlave CANopen options for enclosure configurationSafe standstill for power circuitPTC relay for power circuitPt100 relay for power circuitInsulation monitoring for power circuitDesign for IT networks for power circuitExternal 230 V supply terminals for power circuitBuffer voltage 24 V DC power supply for power circuitEnclosure lighting for power circuitKey switch (local/remote) for power circuitMotor heating for power circuitExternal motor fan for power circuitVoltmeter for power circuitDoor handle for main switch for power circuitLine contactor for power circuit12-pulse supply for power circuitAmmeter for power circuitEnclosure heating for power circuitMotor choke for power circuitCable entry via the top for power circuitEnclosure plinth for power circuitRelay output C/O for control circuitExternal 24 V DC supply terminals for power circuitCircuit breaker for power circuitLine reactor for power circuitControl terminals for control circuitAdaptor for 115 V logic inputs for control circuitIsolated amplifier for control circuit option cardCommunication card for Modbus TCP/IPCommunication card for FipioCommunication card for Modbus/Uni-TelwayCommunication card for Modbus PlusCommunication card for Ethernet/IPCommunication card for DeviceNetCommunication card for Profibus DPCommunication card for Profibus DP V1Communication card for Interbus-SCommunication card for CC-LinkCommunication card for LonWorksCommunication card for METASYS N2Communication card for APOGEE FLNCommunication card for BACnetBasic I/O extension cardExtended I/O extension cardController inside programmable cardMulti-pump cardEncoder interface cards operating positionVertical +/- 10 degree colour of enclosureLight grey (RAL 7035) colour of base of enclosureDark grey (RAL 7022) width1800 mm height2009 mm depth642 mm net weight950 kg Environment electromagnetic compatibilityElectrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-61.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 standardsEN 61800-3 environments 1 category C3EN 55011 class A group 2EN/IEC 61800-3EN 61800-3 environments 2 category C3EN/IEC 61800-5-1 product certificationsGOSTATEX markingCE pollution degree2 conforming to EN/IEC 61800-5-1 noise level77 dB vibration resistance1.5 mm (f= 3…10 Hz) conforming to EN/IEC 60068-2-60.6 gn (f= 10…200 Hz) conforming to EN/IEC 60068-2-63M3 conforming to EN/IEC 60721-3-3 shock resistance4 gn for 11 ms conforming to EN/IEC 60068-2-273M2 conforming to EN/IEC 60721-3-3 environmental characteristic3C2 without condensation conforming to IEC 60721-3-33S2 without condensation conforming to IEC 60721-3-33K3 without condensation conforming to IEC 60721-3-3 relative humidity0…95 % ambient air temperature for operation0…40 °C (without)40…50 °C (with current derating of 1.2 % per °C) ambient air temperature for storage-25…70 °C volume of cooling air5500 m3/h operating altitude<= 1000 m without1000...3000 m with current derating 1 % per 100 m Contractual warranty Warranty18 months
User guideFormatSizeAdd to My DocumentsSize pdfSize 180.5 KBDate 4/23/14DescriptionShort-Circuit Current Ratings (SCCR) and branch circuit protection
- All Languages11
Software and FirmwareLanguage
Software - ReleasedFormatSizeAdd to My DocumentsDTM filesFormatSizeAdd to My DocumentsSize zipSize 422.7 MBDate 5/2/18
- All Languages2
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
Dimensions DrawingsIP 23 Floor-Standing Enclosure with Separate Air FlowsDimensions
NOTE: For each floor-standing enclosure added, allow a 4 mm/0.15 in. space for the seal.
Connections and SchemaFloor-Standing Enclosure with Separate Air FlowsStandard 6-pulse DesignA1DriveA2EnclosureF1FusesIL1Optional line chokeKM1Optional line contactorMMotorQ1SwitchQ2Optional circuit breaker(1)Filter(2)Control(3)Relay control(4)Reference potentiometer(5)PLC(6)Optional motor chokeOptional 12-pulse DesignA1DriveA2EnclosureF1FusesIL1Optional line chokeKM1Optional line contactorMMotorQ1Switch(1)Filter(2)Control(3)Relay control(4)Reference potentiometer(5)PLC(6)Optional motor choke
Performance CurvesIP 23 Floor-Standing Enclosure with Separate Air FlowsDerating Curves
The derating curves for the drive nominal current (In) are dependent on the temperature and switching frequency. For intermediate temperatures, interpolate between 2 curves.
NOTE: The drive will reduce the switching frequency automatically in the event of excessive temperature rise.XSwitching frequency (kHz)
NOTE: The temperatures shown correspond to the temperature of the air entering the enclosure.