ATV61HU55M3S337 may be replaced by any of the following products:
The maximum number of products that can be compared is 4. Remove already added products.
- Reason for Substitution: End of life
- Substitution date: 01 May 2014
Main range of productAltivar 61 product or component typeVariable speed drive product specific applicationPumping and ventilation machine component nameATV61 motor power kW4 kW, single phase at 200...240 V5.5 kW, 3 phases at 200...240 V motor power hp5 hp, single phase at 200...240 V7.5 hp, 3 phases at 200...240 V power supply voltage200...240 V - 15...10 % supply number of phasesSingle phase3 phases line current29.9 A for 240 V single phase 4 kW / 5 hp30.8 A for 240 V 3 phases 5.5 kW / 7.5 hp34.9 A for 200 V single phase 4 kW / 5 hp35 A for 200 V 3 phases 5.5 kW / 7.5 hp EMC filterLevel 3 EMC filter variantReinforced version assembly styleWith heat sink apparent power7 kVA at 240 V single phase 4 kW / 5 hp12.8 kVA at 240 V 3 phases 5.5 kW / 7.5 hp maximum prospective line Isc22 kA for 3 phases5 kA for single phase maximum transient current21 A for 60 s, single phase33 A for 60 s, 3 phases nominal switching frequency12 kHz switching frequency1...16 kHz adjustable12...16 kHz with derating factor asynchronous motor controlVoltage/frequency ratio, 2 pointsFlux vector control without sensor, standardVoltage/frequency ratio - Energy Saving, quadratic U/fVoltage/frequency ratio, 5 points synchronous motor control profileVector control without sensor, standard communication port protocolModbusCANopen type of polarizationNo impedance for Modbus option cardCommunication card for APOGEE FLNCommunication card for BACnetCommunication card for CC-LinkController inside programmable cardCommunication card for DeviceNetCommunication card for Ethernet/IPCommunication card for FipioI/O extension cardCommunication card for Interbus-SCommunication card for LonWorksCommunication card for METASYS N2Communication card for Modbus PlusCommunication card for Modbus TCPCommunication card for Modbus/Uni-TelwayMulti-pump cardCommunication card for Profibus DPCommunication card for Profibus DP V1 Complementary product destinationSynchronous motorsAsynchronous motors power supply voltage limits170…264 V power supply frequency50...60 Hz - 5...5 % power supply frequency limits47.5...63 Hz continuous output current27.5 A at 12 kHz, 230 V - 3 phases17.5 A at 12 kHz, 230 V - single phase output frequency0.1…599 Hz speed range1…100 in open-loop mode, without speed feedback speed accuracy+/- 10 % of nominal slip 0.2 Tn to Tn without speed feedback torque accuracy+/- 15 % in open-loop mode, without speed feedback transient overtorque130 % of nominal motor torque +/- 10 % for 60 s braking torque<= 125 % with braking resistor30 % without braking resistor regulation loopFrequency PI regulator motor slip compensationCan be suppressedAutomatic whatever the loadNot available in voltage/frequency ratio (2 or 5 points)Adjustable diagnostic1 LED (red)drive voltage: output voltage<= power supply voltage electrical isolationBetween power and control terminals type of cable for mounting in an enclosureWith an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVCWith UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVCWithout mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVCWithout mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR electrical connectionTerminal 2.5 mm² / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)Terminal 6 mm² / AWG 8 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) tightening torque0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)3 N.m, 26.5 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) supplyInternal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC, +/- 5 %, <10 mA with overload and short-circuit protectionInternal supply: 24 V DC (21…27 V), <200 mA with overload and short-circuit protectionExternal supply: 24 V DC (19…30 V) analogue input number2 analogue input typeAI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + signAI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bitsAI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits sampling time2 ms +/- 0.5 ms (AI1-/Al1+) - analog input2 ms +/- 0.5 ms (Al2) - analog input2 ms +/- 0.5 ms (AO1) - analog output2 ms +/- 0.5 ms (LI1...LI5) - discrete input2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input absolute accuracy precision+/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C+/- 0.6 % (AI2) for a temperature variation 60 °C+/- 1 % (AO1) for a temperature variation 60 °C linearity error+/- 0.15 % of maximum value (AI1-/Al1+)+/- 0.15 % of maximum value (AI2)+/- 0.2 % (AO1) analogue output number1 analogue output typeAO1 software-configurable current, analogue output range 0...20 mA, impedance: 500 Ohm, resolution 10 bitsAO1 software-configurable voltage, analogue output range 0...10 V DC, impedance: 470 Ohm, resolution 10 bitsAO1 software-configurable logic output 10 V, 20 mA discrete output number2 discrete output typeConfigurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cyclesConfigurable relay logic: (R2A, R2B) NO - 100000 cycles maximum response time<= 100 ms in STO (Safe Torque Off)R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 msR2A, R2B <= 7 ms, tolerance +/- 0.5 ms minimum switching current3 mA at 24 V DC for configurable relay logic maximum switching currentR1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 msR1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 msR1, R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 msR1, R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms discrete input number7 discrete input typeProgrammable (LI1...LI5)24 V DC (<= 30 V), with level 1 PLC - 3500 OhmSwitch-configurable (LI6)24 V DC (<= 30 V), with level 1 PLC - 3500 OhmSwitch-configurable PTC probe (LI6)0…6 probes - 1500 OhmSafety input (PWR)24 V DC (<= 30 V) - 1500 Ohm discrete input logicNegative logic (sink) (LI1...LI5), > 16 V (state 0), < 10 V (state 1)Positive logic (source) (LI1...LI5), < 5 V (state 0), > 11 V (state 1)Negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1)Positive logic (source) (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1) acceleration and deceleration rampsLinear adjustable separately from 0.01 to 9000 sS, U or customizedAutomatic adaptation of ramp if braking capacity exceeded, by using resistor braking to standstillBy DC injection protection typeAgainst exceeding limit speed: driveAgainst input phase loss: driveBreak on the control circuit: driveInput phase breaks: driveLine supply overvoltage: driveLine supply undervoltage: driveOvercurrent between output phases and earth: driveOverheating protection: driveOvervoltages on the DC bus: drivePower removal: driveShort-circuit between motor phases: driveThermal protection: driveMotor phase break: motorPower removal: motorThermal protection: motor insulation resistance> 1 mOhm 500 V DC for 1 minute to earth frequency resolutionAnalog input: 0.024/50 HzDisplay unit: 0.1 Hz connector type1 RJ45 (on front face) for Modbus1 RJ45 (on terminal) for ModbusMale SUB-D 9 on RJ45 for CANopen physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus transmission rate4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal9600 bps, 19200 bps for Modbus on front face20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen data format8 bits, 1 stop, even parity for Modbus on front face8 bits, odd even or no configurable parity for Modbus on terminal number of addresses1…127 for CANopen1…247 for Modbus method of accessSlave CANopen markingCE operating positionVertical +/- 10 degree net weight5.5 kg width175 mm height295 mm depth187 mm Environment noise level55.6 dB conforming to 86/188/EEC dielectric strength2830 V DC between earth and power terminals4230 V DC between control and power terminals electromagnetic compatibilityConducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 standardsUL Type 1EN 61800-3 environments 1 category C3EN 61800-3 environments 2 category C3IEC 60721-3-3 class 3C2EN 55011 class A group 2EN/IEC 61800-3EN/IEC 61800-5-1 product certificationsGOSTNOM 117ULCSAC-TickDNV pollution degree2 conforming to EN/IEC 61800-5-1 degree of proctectionIP20 on upper part without blanking plate on cover conforming to EN/IEC 60529IP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1IP21 conforming to EN/IEC 60529IP21 conforming to EN/IEC 61800-5-1IP41 on upper part conforming to EN/IEC 60529IP41 on upper part conforming to EN/IEC 61800-5-1IP54 on lower part conforming to EN/IEC 60529IP54 on lower part conforming to EN/IEC 61800-5-1 vibration resistance1 gn (f= 13…200 Hz) conforming to EN/IEC 60068-2-61.5 mm peak to peak (f= 3…13 Hz) conforming to EN/IEC 60068-2-6 shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27 relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for operation-10…50 °C (without derating)50…60 °C (with derating factor) ambient air temperature for storage-25…70 °C operating altitude<= 1000 m without derating1000...3000 m with current derating 1 % per 100 m Contractual warranty Warranty18 months
CertificateFormatSizeAdd to My DocumentsEnd of Life InformationFormatSizeAdd to My Documents
- All Languages5
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.