Welcome to the Schneider Electric Website

Welcome to our website.

Select your location

Welcome the the Schneider Electric French website. It looks like you are located in the United States, would you like to change your location?

Traduisez en francais
View all   Altivar Easy 310
ATV310HU30N4E Product picture Schneider Electric

ATV310HU30N4E

ATV310HU30N4E Product picture Schneider Electric
ATV310HU30N4E

variable speed drive ATV310 - 3 kW - 4 hp - 380...460 V - 3 phase

Show more characteristics
The maximum number of products that can be compared is 4. Remove already added products.

  • Main
    range of product
    Easy Altivar 310
    product or component type
    Variable speed drive
    product specific application
    Simple machine
    assembly style
    With heat sink
    device short name
    ATV310
    network number of phases
    Three phase
    [Us] rated supply voltage
    380...460 V - 15...10 %
    motor power kW
    3 kW
    motor power hp
    4 hp
    noise level
    50 dB
    Complementary
    product destination
    Asynchronous motors
    quantity per set
    Set of 1
    EMC filter
    Without EMC filter
    type of cooling
    Integrated fan
    supply frequency
    50/60 Hz +/- 5 %
    communication port protocol
    Modbus
    connector type
    RJ45 (on front face) for Modbus
    physical interface
    2-wire RS 485 for Modbus
    transmission frame
    RTU for Modbus
    transmission rate
    4800 bit/s
    9600 bit/s
    19200 bit/s
    38400 bit/s
    number of addresses
    1…247 for Modbus
    communication service
    Read holding registers (03) 29 words
    Write single register (06) 29 words
    Write multiple registers (16) 27 words
    Read/write multiple registers (23) 4/4 words
    Read device identification (43)
    line current
    9.2 A
    apparent power
    7.3 kVA
    prospective line Isc
    5 kA
    continuous output current
    7.1 A at 4 kHz
    maximum transient current
    10.7 A for 60 s
    power dissipation in W
    80.24 W at In
    speed drive output frequency
    0.5…400 Hz
    nominal switching frequency
    4 kHz
    switching frequency
    2...12 kHz adjustable
    speed range
    1…20
    transient overtorque
    170…200 % of nominal motor torque depending on drive rating and type of motor
    braking torque
    Up to 150 % of nominal motor torque with braking resistor at high inertia
    Up to 70 % of nominal motor torque without braking resistor
    asynchronous motor control profile
    Energy saving ratio
    Sensorless flux vector control
    Quadratic voltage/frequency ratio
    motor slip compensation
    Preset in factory
    Adjustable
    output voltage
    380...460 V three phase
    electrical connection
    Terminal, clamping capacity: 1.5...4 mm² (L1, L2, L3, PA/+, PB, U, V, W)
    tightening torque
    1.2…1.4 N.m
    insulation
    Electrical between power and control
    supply
    Internal supply for reference potentiometer: 5 V (4.75…5.25 V)DC, <10 mA with overload and short-circuit protection
    Internal supply for logic inputs: 24 V (20.4…28.8 V)DC, <100 mA with overload and short-circuit protection
    analogue input number
    1
    analogue input type
    Configurable current AI1 0...20 mA 250 Ohm
    Configurable voltage AI1 0...10 V 30 kOhm
    Configurable voltage AI1 0...5 V 30 kOhm
    discrete input number
    4
    discrete input type
    Programmable LI1...LI4 24 V 18...30 V
    discrete input logic
    Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
    Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)
    sampling duration
    10 ms for analogue input
    20 ms, tolerance +/- 1 ms for logic input
    linearity error
    +/- 0.3 % of maximum value for analogue input
    analogue output number
    1
    analogue output type
    AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits
    AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits
    discrete output number
    2
    discrete output type
    Logic output LO+, LO-
    Protected relay output R1A, R1B, R1C 1 C/O
    minimum switching current
    5 mA at 24 V DC for logic relay
    maximum switching current
    2 A at 250 V AC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay
    2 A at 30 V DC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay
    3 A at 250 V AC on resistive load cos phi = 1 L/R = 0 ms for logic relay
    4 A at 30 V DC on resistive load cos phi = 1 L/R = 0 ms for logic relay
    acceleration and deceleration ramps
    U
    S
    Linear from 0...999.9 s
    braking to standstill
    By DC injection, <30 s
    protection type
    Line supply overvoltage
    Line supply undervoltage
    Overcurrent between output phases and earth
    Overheating protection
    Short-circuit between motor phases
    Against input phase loss in three-phase
    Thermal motor protection via the drive by continuous calculation of I²t
    frequency resolution
    Analog input: converter A/D, 10 bits
    Display unit: 0.1 Hz
    time constant
    20 ms +/- 1 ms for reference change
    operating position
    Vertical +/- 10 degree
    height
    151 mm
    width
    140 mm
    depth
    184 mm
    net weight
    1.8 kg
    Environment
    electromagnetic compatibility
    Electrical fast transient/burst immunity test - test level: level 4 conforming to EN/IEC 61000-4-4
    Electrostatic discharge immunity test - test level: level 3 conforming to EN/IEC 61000-4-2
    Immunity to conducted disturbances - test level: level 3 conforming to EN/IEC 61000-4-6
    Radiated radio-frequency electromagnetic field immunity test - test level: level 3 conforming to EN/IEC 61000-4-3
    Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11
    Surge immunity test - test level: level 3 conforming to EN/IEC 61000-4-5
    standards
    EN/IEC 61800-3
    EN/IEC 61800-5-1
    IP degree of protection
    IP20 without blanking plate on upper part
    IP41 top
    pollution degree
    2 conforming to EN/IEC 61800-5-1
    environmental characteristic
    Dust pollution resistance class 3S2 conforming to EN/IEC 60721-3-3
    Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3
    shock resistance
    15 gn conforming to EN/IEC 60068-2-27 for 11 ms
    relative humidity
    5…95 % without condensation conforming to IEC 60068-2-3
    5…95 % without dripping water conforming to IEC 60068-2-3
    ambient air temperature for storage
    -25…70 °C
    ambient air temperature for operation
    -10…55 °C without derating
    55…60 °C protective cover from the top of the drive removed with current derating 2.2 % per °C
    operating altitude
    <= 1000 m without derating
    Packing Units
    Package 1 Weight
    2.190 kg
    Package 1 Height
    1.510 dm
    Package 1 width
    1.400 dm
    Package 1 Length
    1.840 dm
  • View more View less

    Documents

    Language
    • All Languages9
    • English9
    • Chinese2
    Catalogue
    Format
    Size
    Date
    Add to My Documents
    prp.document.label.format pdf
    Size 3.2 MB
    Date 2019/12/16
    User guide
    Format
    Size
    Date
    Add to My Documents
    Altivar Easy ATV310 Complete parameters list (Version 05)
    Description
    ATV310 Complete parameters list
    prp.document.label.format pdf
    Size 552.4 KB
    Date 2020/04/01
    Description
    ATV310 Complete parameters list
    prp.document.label.format pdf
    Size 7.8 MB
    Date 2018/04/05
    ATV310 - Communication Parameters (Version 1.4)
    Description
    ATV310 - Communication Parameters
    prp.document.label.format xls
    Size 263.5 KB
    Date 2016/10/12
    Description
    ATV310 - Communication Parameters
    1) Altivar Easy Getting started with ATV310 (Version 01)
    Description
    Getting started with ATV310
    prp.document.label.format pdf
    Size 1.1 MB
    Date 2016/01/28
    Description
    Getting started with ATV310
    prp.document.label.format pdf
    Size 638.1 KB
    Date 2014/07/03
    Certificate
    Format
    Size
    Date
    Add to My Documents
    prp.document.label.format pdf
    Size 690.6 KB
    Date 2016/08/02
    Product Environmental Profile
    Format
    Size
    Date
    Add to My Documents
    Instruction Sheet: China RoHS - Hazardous Substances Table (Version 01)
    Description
    This table is made according to SJ/T 11364. O: indicates that the concentration of hazardous substance in all of the homogeneous materials for this part is below the limit as stipulated in GB/T 26572. X: indicates that concentration of hazardous substance in at least one of the homogeneous materials used for this part is above the limit as stipulated in GB/T 26572
    prp.document.label.format pdf
    Size 1.1 MB
    Date 2016/05/30
    Description
    This table is made according to SJ/T 11364. O: indicates that the concentration of hazardous substance in all of the homogeneous materials for this part is below the limit as stipulated in GB/T 26572. X: indicates that concentration of hazardous substance in at least one of the homogeneous materials used for this part is above the limit as stipulated in GB/T 26572
  • Technical FAQs

    No results found
    Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
  • Dimensions Drawings

    Dimensions


    Dimensions in mm

    a

    b

    c

    G

    H

    H1

    Ø

    For screws

    140

    171

    151

    126

    157

    184

    5

    M4

    Dimensions in in.

    a

    b

    c

    G

    H

    H1

    Ø

    For screws

    5.51

    6.73

    5.94

    4.96

    6.18

    7.24

    0.20

    M4


  • Mounting and Clearance

    Mounting Recommendations
    Clearance


    Mounting Types

    Mounting Type A


    Mounting Type B


    Remove the protective cover from the top of the drive.


  • Connections and Schema

    Three-Phase Power Supply Wiring Diagram


    A1 :
    Drive
    KM1 :
    Contactor (only if a control circuit is needed)
    P1 :
    2.2 kΩ reference potentiometer. This can be replaced by a 10 kΩ potentiometer (maximum).
    Q1 :
    Circuit breaker
    R :
    Braking resistor (optional)
    (1)
    Negative logic (Sink)
    (2)
    Positive logic (Source) (factory set configuration)
    (3)
    0...10 V or 0...20 mA
    (4)
    Line choke three-phase (optional)