Introduction

• create Alarms under PME Web Application for Smartlink I/O Channels
• trigger an event for Report Subscription

Create Alarm under PME 9.0 Web Application

Expose Custom Measurement with Manual Data Editor

Step	Description
1	Open Manual Data Editor (MDE) from Management Console
2	On the MDE -> click on “Create New Measurement”
3	To create a Measurement for I1 Input for CH1 Channel: enter the exact name “CH1 Input 1 Status” in the Measurement Name Status uncheck “Is Cumulative” check “Average”
4	To create a Measurement for I2 Input for CH1 Channel, enter “CH1 Input 2 Status”
5	To create a Measurement for Q Output for CH1 Channel, enter “CH1 Output Status”
6	Repeat steps 3 to 5 to create the Measurements for: the 10 other I/O Channels of your Smartlink A9XMSB11 the 6 other I/O Channels of your Smartlink A9XMZA08
7	Close all the MDE related windows.

Create Event under the VIP with Designer

Create Alarm for Smartlink I/O Channel under Web Application

Step	Description
1	Go under the Windows Services and restart “ION Application Modules Core Services Host” service. This will force the new created measurements available under the Web Application.
2	Log in to the PME Web Application.
3	Go under SETTINGS menu -> Configuration Tools -> Alarm Configuration and click on “Alarm Rule” button.
4	Select the following template: User Defined -> Realtime Digital Setpoint
5	Under “Available Measurements” go under the “Custom” folder and select the measurements related to the Smartlink I/O Channel. You can apply the “CH” filter if you have too many Measurements in the “Custom” folder. If you want to create alarm only for I1 and I2, then do not select the Output. You will be able to create a separate alarm later for the Output.
6	Gives a specific Alarm Name. Choose an Active and Inactive Condition Label that fit with your application. See the example below. Select also an Alarm Priority: 192 is the threshold for High Priority Alarm. You can choose a lower value. Trigger will be “FALSE (equal to 0)” if the I1 or I2 of the I/O Channel is 0DC (Breaker Open).
7	Select the sources to which the alarms will apply. You must have some Smartlink devices declared in the Management Console.
8	Create a Schedule if necessary.
9	Enter a Rule Name and click on “Finish” button.
10	Check that the rule is enabled.

Testing Smartlink IO Alarm on PME Web Application

I1, I2 Input Alarming

Step	Description
1	Change the status of an input of your Smartlink.
2	Check that an alarm is raised on the PME Web Interface. On the example below I have some alarms on I1, I2 for Channels 1 & 2 for a Smartlink SIB.
3	Restore the previous status on your Smartlink Input.
4	Check on PME that the alarms are no more active.
5	On the Event History you will be able to check the Pick up and Drop out events associated to the previous alarm.

Q Output Alarming

Step	Description
1	Change the status of an output of your Smartlink.
2	Check that an alarm is raised on the PME Web Interface. On the example below I have an alarm on an output for Channels 2 for a Smartlink SIB.
3	Restore the previous status on your Smartlink Output.
4	Check on PME that the alarms are no more active.
5	On the Event History you will be able to check the Pick up and Drop out events associated to the previous alarm.

Create Report Subscription on Trigger

Event Watcher for Smartlink IO

Step	Description
1	Open the Events Watcher from Management Console: Tools -> Event Watcher
2	Select the “Templates” tab.
3	Give a name to the Template. By example “Smartlink-IO”
4	Under section “Edit Smartlink-IO” : click on “New” Button check the “Cause” field and enter: “CH{0.EN_US} Output Status*” check the “Cause Value” field and enter: “1.000” click on “New” Button check the “Cause” field and enter: “CHx Input {0.EN_US} Status*” (replace ‘x’ by the Smartlink Channel) check the “Cause Value” field and enter: “1.000” Repeat steps 5 and 6 for any channel you want to monitor Click on “Apply” button The Templates tab of the Event Watcher Manager should look like the example below.
5	Select the “Event Watchers” tab and click on the “New” button.
6	Under the section “Edit New Event Watcher”: Give a name to the watcher. Example : “Smartlink-IO-Watch” Select the template created in the previous steps Select the Devices (Smartlink devices available under Management Console) Click on “Apply button The Event Watchers tab of the Event Watcher Manager should look like the example below.

Create a Report Subscription on Trigger

1. Check your SMTP parameters under Management Console -> Tool -> Report Configuration -> Subscriptions
2. You must have created your own Report from an available template (Report -> Add Report)

Step	Description
1	Log in to the PME Web Application and Select “Report” tab
2	Click on the Burger menu -> Manage Subsciptions
3	Click on “Add Subscriptions…” button -> select your Report -> click on Next
4	Under the Subscription parameters, select “On trigger” and chose the Event Watcher you defined before.

Released for:Schneider Electric Indonesia