Issue:
What are the forms to add a TeSys T to a starter? And which TeSys T module is used?
Product Line:
NEMA Type S Starters
Environment:
North American Market
Cause:
Product Selection
Resolution:
The forms, and devices, used are dependent upon NEMA size, full load amperage, and control voltage. Please see the table below for the forms and part numbers.
* NEMA size 6 contactors are only rated up to 810 amps (and should not be used for greater than 810 amps), as such when the contactor rating is programmed in to the TeSys T as 810 amps the device will not let you set a full load amperage over 810 amps.
Note: To order a NEMA starter with a TeSys T motor management controller the product selector should be used.
What are the forms to add a TeSys T to a starter? And which TeSys T module is used?
Product Line:
NEMA Type S Starters
Environment:
North American Market
Cause:
Product Selection
Resolution:
The forms, and devices, used are dependent upon NEMA size, full load amperage, and control voltage. Please see the table below for the forms and part numbers.
| NEMA Size | Range | Communication Protocol | Form | TeSys T Part Number | ||
| Control Voltage | Control Voltage | |||||
| 100-240VAC | 24VDC | 100-240VAC | 24VDC | |||
| 1 | .4-8 | Modbus | H612 | H712 | LTMR08MFM | LTMR08MBD |
| ProfiBus | H613 | H713 | LTMR08PFM | LTMR08PBD | ||
| CANopen | H614 | H714 | LTMR08CFM | LTMR08CBD | ||
| DeviceNet | H615 | H715 | LTMR08DFM | LTMR08DBD | ||
| Ethernet TCP/IP | H616 | H716 | LTMR08EFM | LTMR08EBD | ||
| 1.35-27 | Modbus | H622 | H722 | LTMR27MFM | LTMR28MBD | |
| ProfiBUS | H623 | H723 | LTMR27PFM | LTMR08PBD | ||
| CANopen | H624 | H724 | LTMR27CFM | LTMR27CBD | ||
| DeviceNet | H625 | H725 | LTMR27DFM | LTMR27DBD | ||
| Ethernet TCP/IP | H626 | H726 | LTMR27EFM | LTMR27EBD | ||
| 2, 3 | 5.0-100 | Modbus | H632 | H732 | LTMR100MFM | LTMR100MBD |
| ProfiBus | H633 | H733 | LTMR100PFM | LTMR100PBD | ||
| CANopen | H634 | H734 | LTMR100CFM | LTMR100CBD | ||
| DeviceNet | H635 | H735 | LTMR100DFM | LTMR100DBD | ||
| Ethernet TCP/IP | H636 | H736 | LTMR100EFM | LTMR100EBD | ||
| 4 | 8-160 (CT 300:5 3 turns) | Modbus | H652 | H752 | LTMR08MFM | LTMR08MBD |
| ProfiBus | H653 | H753 | LTMR08PFM | LTMR08PBD | ||
| CANopen | H654 | H754 | LTMR08CFM | LTMR08CBD | ||
| DeviceNet | H655 | H755 | LTMR08DFM | LTMR08DBD | ||
| Ethernet TCP/IP | H656 | H756 | LTMR08EFM | LTMR08EBD | ||
| 5 | 24-480 (CT 300:5 1 turn) | Modbus | H662 | H762 | LTMR08MFM | LTMR08MBD |
| ProfiBus | H663 | H763 | LTMR08PFM | LTMR08PBD | ||
| CANopen | H664 | H764 | LTMR08CFM | LTMR08CBD | ||
| DeviceNet | H665 | H765 | LTMR08DFM | LTMR08DBD | ||
| Ethernet TCP/IP | H666 | H766 | LTMR08EFM | LTMR08EBD | ||
| 6 | 48-960 (CT 600:5 1 turn)* | Modbus | H672 | H772 | LTMR08MFM | LTMR08MBD |
| ProfiBus | H673 | H773 | LTMR08PFM | LTMR08PBD | ||
| CANopen | H674 | H774 | LTMR08CFM | LTMR08CBD | ||
| DeviceNet | H675 | H775 | LTMR08DFM | LTMR08DBD | ||
| Ethernet TCP/IP | H676 | H776 | LTMR08EFM | LTMR08EBD | ||
* NEMA size 6 contactors are only rated up to 810 amps (and should not be used for greater than 810 amps), as such when the contactor rating is programmed in to the TeSys T as 810 amps the device will not let you set a full load amperage over 810 amps.
Note: To order a NEMA starter with a TeSys T motor management controller the product selector should be used.
Released for:Schneider Electric USA
