Issue:
Altivar Process Drive setup to communicate over CanOpen

Product Line:
Altivar Process Drive (ATV630, ATV930, ATV650, ATV950, ATV660, ATV960, ATV680, ATV980)

Environment:
All serial numbers for Altivar Process Drive

Cause:
N/A

Resolution:
This FAQ will go over some basic settings to check. For a more detailed list of procedures on setting up the drive for CanOpen please reference the manuals attached.

EDS Files

• Download and import CanOpen EDS files
  • ATV600
    • ​CANopen v1.1 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV600_CANopen_EDS_V1_1/
    • CANopen v1.2 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV600_CANopen_EDS_V1_2/
    • CANopen v1.3 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV600_CANopen_EDS_V1_3/
    • CANopen v1.4 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV600_CANopen_EDS_V1_4/
    • CANopen v1.5 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV600_CANopen_EDS_V1_5/
    • CANopen v1.6 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV600_CANopen_V1_6/
      
  • ATV900​
    • CANopen v1.1 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV900_CANopen_V1_1/
    • CANopen v1.2 - VW3A36x8: https://www.se.com/ww/en/download/document/ATV900_CANopen_V1_2

Basic Settings
- Programming with the Drive

• Program Communication Settings:
  • [Communication] COM, [CANopen] CnO
    • [CANopen Address] AdCo
      • This is a read/write parameter. The parameter number is 6051 via Modbus access
    • [CANopen Baudrate] bdCO
      • ​This is a read/write parameter. The parameter number is 6053 via Modbus access.
    • [CANopen Error] ErCO
      • ​This is a read-only Parameter. The parameter number is 6056 via Modbus access..
• Program Command Settings:
  • [Complete settings] [Command and Reference]
    • ​For command speed from Network, program:
      • [Ref Freq 1 Config] Fr1 - Set to [CANopen] CAn
      • [Ref 1B switching] rCb - Set to [Ref Freq Channel 1] Fr1
      • [Control Mode] CHCF - Set to [Not separ.] SIM
    • ​​Video: Setting an Auto/Manual or Reference Switching on the Altivar Process Drives
      • https://www.se.com/us/en/en/faqs/content/?id=FA294131
• Powercycle the drive

​- Programming with SoMove

• [Parameters List] [Fieldbus] [Slot A - CanOpen]
  • Configure
    • CanOpen Address, Baud Rate & Error

Communicate with the Drive

• Sending a command to the drive
• Configuration of the Drive for Operation in I/O Profile
  • [Complete Settings] [Command and Reference] [Control Mode] - Set to IO
  • Command Word - CanOpen Register 2037/2
    Speed Reference Word - CanOpen Registers 2037/3 (Hz) or 2038/3 (rpm)
  • 16 bit word (Bit 0, 1, 2..... 15)
  • Start/Stop for FWD command must turn on bit 0
    • Write a 1 to start
    • Write a 0 to stop
  • Bit 1 to 15 are assignable like logic inputs
    • Example: To assign a fault reset to bit 7 - [Fault reset] - Set to Cd07 (Reference Programming manual for more details)
• Using CIA402 (DriveCom Profile)
  • Works with other assemblies
  • [Complete Settings] [Command and Reference] [Control Mode] to [Not separ.] or [Separate]
  • Command Word - CanOpen Register 2037/2
    Speed Reference Word - CanOpen Registers 2037/3 (Hz) or 2038/3 (rpm)
  • No 16 bit word
  • Start/Stop
    • Sequence of values must be written to the drive
    • 6, 7 and 15
    • Toggle between 7 and 15 to start and stop or "RDY" to "RUN"

Đã phát hành cho: Schneider Electric Việt Nam