Main range of productAltivar 12 product or component typeVariable speed drive product destinationAsynchronous motors product specific applicationSimple machine assembly styleOn base plate component nameATV12 quantity per setSet of 1 EMC filterIntegrated built-in fanWithout network number of phases1 phase [Us] rated supply voltage200...240 V - 15...10 % motor power kW0.55 kW motor power hp0.75 hp communication port protocolModbus line current8 A at 200 V6.7 A at 240 V speed range1…20 transient overtorque150…170 % of nominal motor torque depending on drive rating and type of motor asynchronous motor control profileQuadratic voltage/frequency ratioSensorless flux vector controlVoltage/frequency ratio (V/f) IP degree of protectionIP20 without blanking plate on upper part noise level0 dB Complementary supply frequency50/60 Hz +/- 5 % connector type1 RJ45 (on front face) for Modbus physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus transmission rate4800 bit/s9600 bit/s19200 bit/s38400 bit/s number of addresses1…247 for Modbus communication serviceRead holding registers (03) 29 wordsWrite single register (06) 29 wordsWrite multiple registers (16) 27 wordsRead/write multiple registers (23) 4/4 wordsRead device identification (43) prospective line Isc1 kA continuous output current3.5 A at 4 kHz maximum transient current5.3 A for 60 s speed drive output frequency0.5…400 Hz nominal switching frequency4 kHz switching frequency2...16 kHz adjustable4...16 kHz with derating factor braking torqueUp to 70 % of nominal motor torque without braking resistor motor slip compensationPreset in factoryAdjustable output voltage200...240 V 3 phases electrical connectionTerminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC) tightening torque0.8 N.m insulationElectrical between power and control supplyInternal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protectionInternal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection analogue input number1 analogue input typeConfigurable current AI1 0...20 mA 250 OhmConfigurable voltage AI1 0...10 V 30 kOhmConfigurable voltage AI1 0...5 V 30 kOhm discrete input number4 discrete input typeProgrammable LI1...LI4 24 V 18...30 V discrete input logicNegative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhmPositive logic (source), 0...< 5 V (state 0), > 11 V (state 1) sampling duration20 ms, tolerance +/- 1 ms for logic input10 ms for analogue input linearity error+/- 0.3 % of maximum value for analogue input analogue output number1 analogue output typeAO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bitsAO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits discrete output number2 discrete output typeLogic output LO+, LO-Protected relay output R1A, R1B, R1C 1 C/O minimum switching current5 mA at 24 V DC for logic relay maximum switching current2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay acceleration and deceleration rampsUSLinear from 0 to 999.9 s braking to standstillBy DC injection, <30 s protection typeLine supply overvoltageLine supply undervoltageOvercurrent between output phases and earthOverheating protectionShort-circuit between motor phasesAgainst input phase loss in three-phaseThermal motor protection via the drive by continuous calculation of I²t frequency resolutionAnalog input: converter A/D, 10 bitsDisplay unit: 0.1 Hz time constant20 ms +/- 1 ms for reference change markingCE operating positionVertical +/- 10 degree height143 mm width72 mm depth102.2 mm product weight0.7 kg motor starter typeVariable speed drive Environment electromagnetic compatibilityElectrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3Surge immunity test level 3 conforming to EN/IEC 61000-4-5Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11 electromagnetic emissionRadiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cableConducted emissions with integrated EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 mConducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2...12 kHz shielded motor cable <5 mConducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2, 4 and 16 kHz shielded motor cable <10 mConducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 mConducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 mConducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m product certificationsGOSTULC-TickNOMCSA vibration resistance1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-61.5 mm peak to peak (f = 3…13 Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/IEC 60068-2-6 shock resistance15 gn conforming to EN/IEC 60068-2-27 for 11 ms relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for storage-25…70 °C ambient air temperature for operation-10…40 °C protective cover from the top of the drive removed40…60 °C with current derating 2.2 % per °C operating altitude> 1000...2000 m with current derating 1 % per 100 m<= 1000 m without
User guideFormatSizeAdd to My Documents
- All Languages6
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.