ATV312H037M2 is replaced by:
The maximum number of products that can be compared is 4. Remove already added products.
- Reason for Substitution: End of life
- Substitution date: 03 May 2016
Main range of productAltivar 312 product or component typeVariable speed drive product destinationAsynchronous motors product specific applicationSimple machine assembly styleWith heat sink component nameATV312 motor power kW0.37 kW motor power hp0.5 hp [Us] rated supply voltage200...240 V - 15...10 % supply frequency50...60 Hz - 5...5 % network number of phasesSingle phase line current5.3 A at 200 V, Isc = 1 kA4.4 A at 240 V EMC filterIntegrated apparent power1 kVA maximum transient current5 A for 60 s power dissipation in W41 W at nominal load speed range1…50 asynchronous motor control profileFactory set : constant torqueSensorless flux vector control with PWM type motor control signal electrical connectionAl1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 2.5 mm² AWG 14 supplyInternal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protectionInternal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection communication port protocolModbusCANopen IP degree of protectionIP20 on upper part without cover plateIP21 on connection terminalsIP31 on upper partIP41 on upper part option cardCommunication card for CANopen daisy chainCommunication card for DeviceNetCommunication card for FipioCommunication card for Modbus TCPCommunication card for Profibus DP Complementary supply voltage limits170…264 V prospective line Isc1 kA continuous output current3.3 A at 4 kHz output frequency0…500 kHz nominal switching frequency4 kHz switching frequency2...16 kHz adjustable transient overtorque170…200 % of nominal motor torque braking torque150 % during 60 s with braking resistor100 % with braking resistor continuously150 % without braking resistor regulation loopFrequency PI regulator motor slip compensationAutomatic whatever the loadSuppressableAdjustable output voltage<= power supply voltage tightening torqueAl1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6 N.mL1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 0.8 N.m insulationElectrical between power and control analogue input number3 analogue input typeAI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 OhmAI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 OhmAI3 configurable current 0...20 mA, impedance: 250 Ohm sampling durationAI1, AI2, AI3: 8 ms analogLI1...LI6: 4 ms discrete response timeAOV, AOC 8 ms for analogR1A, R1B, R1C, R2A, R2B 8 ms for discrete linearity error+/- 0.2 % for output analogue output number1 analogue output typeAOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bitsAOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits discrete input logicLogic input not wired (LI1...LI4), < 13 V (state 1)Negative logic (source) (LI1...LI6), > 19 V (state 0)Positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1) discrete output number2 discrete output typeConfigurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cyclesConfigurable relay logic: (R2A, R2B) NC - 100000 cycles minimum switching currentR1-R2 10 mA at 5 V DC maximum switching currentR1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 msR1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 msR1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 msR1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms discrete input number6 discrete input type(LI1...LI6) programmable at 24 V, 0…100 mA for PLC, impedance: 3500 Ohm acceleration and deceleration rampsS, U or customizedLinear adjustable separately from 0.1 to 999.9 s braking to standstillBy DC injection protection typeInput phase breaks: driveLine supply overvoltage and undervoltage safety circuits: driveLine supply phase loss safety function, for three phases supply: driveMotor phase breaks: driveOvercurrent between output phases and earth (on power up only): driveOverheating protection: driveShort-circuit between motor phases: driveThermal protection: motor insulation resistance>= 500 mOhm 500 V DC for 1 minute local signalling1 LED (red)drive voltage: Four 7-segment display unitsCANopen bus status: time constant5 ms for reference change frequency resolutionAnalog input: 0.1...100 HzDisplay unit: 0.1 Hz connector type1 RJ45 for Modbus/CANopen physical interfaceRS485 multidrop serial link transmission frameRTU transmission rate10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen4800, 9600 or 19200 bps for Modbus number of addresses1…127 for CANopen1…247 for Modbus number of drive127 for CANopen31 for Modbus markingCE operating positionVertical +/- 10 degree height145 mm width72 mm depth132 mm net weight1.5 kg Environment dielectric strength2040 V DC between earth and power terminals2880 V AC between control and power terminals electromagnetic compatibility1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3 standardsIEC 61800-5-1IEC 61800-3 product certificationsULC-TickNOMCSADNVGOST pollution degree2 protective treatmentTC vibration resistance1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-61.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-6 shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27 relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for storage-25…70 °C ambient air temperature for operation-10…50 °C without derating (with protective cover on top of the drive)-10…60 °C with derating factor (without protective cover on top of the drive) operating altitude<= 1000 m without derating1000...2000 m with current derating 1 % per 100 m Offer Sustainability Sustainable offer statusGreen Premium product REACh Regulation EU RoHS DirectivePro-active compliance (Product out of EU RoHS legal scope)
EU RoHS Declaration
Mercury freeYes RoHS exemption information China RoHS Regulation Environmental Disclosure Circularity Profile WEEEThe product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins Contractual warranty Warranty18 months
CatalogueFormatSizeAdd to My DocumentsUser guideFormatSizeAdd to My Documentsprp.document.label.format pdfSize 210.6 KBDate 4/29/16DescriptionShort-Circuit Current Ratings (SCCR) and branch circuit protection The table shows recommended fuse ratings for UL and CSA requirements. The components are for use together in accordance with standard UL508CertificateFormatSizeAdd to My DocumentsInstruction sheetFormatSizeAdd to My DocumentsChina RoHS declarationFormatSizeAdd to My DocumentsEnd of Life InformationFormatSizeAdd to My DocumentsEU RoHS DeclarationFormatSizeAdd to My DocumentsMarine certificateFormatSizeAdd to My DocumentsProduct Environmental ProfileFormatSizeAdd to My Documentsprp.document.label.format pdfSize 1.1 MBDate 5/30/16DescriptionThis table is made according to SJ/T 11364. O: indicates that the concentration of hazardous substance in all of the homogeneous materials for this part is below the limit as stipulated in GB/T 26572. X: indicates that concentration of hazardous substance in at least one of the homogeneous materials used for this part is above the limit as stipulated in GB/T 26572REACh DeclarationFormatSizeAdd to My DocumentsSystem user guideFormatSizeAdd to My Documentsprp.document.label.format zipSize 20.4 MBDate 3/1/15
- All Languages42
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.