ATV31H018M3X is replaced by:
The maximum number of products that can be compared is 4. Remove already added products.
- Reason for Substitution: End of life
- Substitution date: 20 April 2009
Main range of productAltivar product or component typeVariable speed drive product specific applicationSimple machine component nameATV31 assembly styleWith heat sink EMC filterWithout EMC filter [Us] rated supply voltage200...240 V - 5...5 % supply frequency50...60 Hz - 5...5 % network number of phases3 phases motor power kW0.18 kW 4 kHz motor power hp0.25 hp 4 kHz line current1.9 A at 240 V2.1 A at 200 V, Isc = 1 kA apparent power0.7 kVA prospective line Isc1 kA nominal output current1.5 A 4 kHz maximum transient current2.3 A for 60 s power dissipation in W23 W at nominal load asynchronous motor control profileSensorless flux vector control with PWM type motor control signalFactory set : constant torque analogue input number3 Complementary product destinationAsynchronous motors supply voltage limits170…264 V network frequency47.5...63 Hz output frequency0.0005…0.5 kHz nominal switching frequency4 kHz switching frequency2...16 kHz adjustable speed range1…50 transient overtorque150…170 % of nominal motor torque braking torque<= 150 % during 60 s with braking resistor100 % with braking resistor continuously150 % without braking resistor regulation loopFrequency PI regulator motor slip compensationAutomatic whatever the loadAdjustableSuppressable output voltage<= power supply voltage electrical connectionAl1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 2.5 mm² AWG 14 tightening torqueAl1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6 N.mL1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 0.8 N.m insulationElectrical between power and control supplyInternal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protectionInternal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection analogue input typeAI3 configurable current 0...20 mA, impedance: 250 OhmAI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 OhmAI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm sampling durationLI1...LI6: 4 ms discreteAI1, AI2, AI3: 8 ms analog response timeAOV, AOC 8 ms for analogR1A, R1B, R1C, R2A, R2B 8 ms for discrete linearity error+/- 0.2 % for output analogue output number2 analogue output typeAOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bitsAOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits discrete input logicPositive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1)Logic input not wired (LI1...LI4), < 13 V (state 1)Negative logic (source) (LI1...LI6), > 19 V (state 0) discrete output number2 discrete output typeConfigurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cyclesConfigurable relay logic: (R2A, R2B) NC - 100000 cycles minimum switching currentR1-R2 10 mA at 5 V DC maximum switching currentR1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 msR1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 msR1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 msR1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms discrete input number6 discrete input type(LI1...LI6) programmable at 24 V, 0…100 mA for PLC, impedance: 3500 Ohm acceleration and deceleration rampsLinear adjustable separately from 0.1 to 999.9 sS, U or customized braking to standstillBy DC injection protection typeInput phase breaks: driveLine supply overvoltage and undervoltage safety circuits: driveLine supply phase loss safety function, for three phases supply: driveMotor phase breaks: driveOvercurrent between output phases and earth (on power up only): driveOverheating protection: driveShort-circuit between motor phases: driveThermal protection: motor insulation resistance>= 500 mOhm 500 V DC for 1 minute display type1 LED (red) for drive voltageFour 7-segment display units for CANopen bus status time constant5 ms for reference change frequency resolutionDisplay unit: 0.1 HzAnalog input: 0.1...100 Hz connector type1 RJ45 for CANopen via VW3 CANTAP2 adaptor1 RJ45 for Modbus physical interfaceRS485 multidrop serial link for CANopen via VW3 CANTAP2 adaptorRS485 multidrop serial link for Modbus transmission frameRTU for CANopen via VW3 CANTAP2 adaptorRTU for Modbus transmission rate10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen via VW3 CANTAP2 adaptor4800, 9600 or 19200 bps for Modbus number of addresses1…127 for CANopen via VW3 CANTAP2 adaptor1…247 for Modbus number of drive127 for CANopen via VW3 CANTAP2 adaptor31 for Modbus markingCE operating positionVertical +/- 10 degree net weight1.3 kg Environment dielectric strength2040 V DC between earth and power terminals2880 V AC between control and power terminals electromagnetic compatibility1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3 standardsEN 50178 product certificationsULN998CSAC-Tick IP degree of protectionOn upper part: IP20 (without cover plate)On connection terminals: IP21On upper part: IP31On upper part: IP41 pollution degree2 protective treatmentTC vibration resistance1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-61.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-6 shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27 relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for storage-25…70 °C ambient air temperature for operation-10…50 °C without (with protective cover on top of the drive)-10…60 °C with derating factor (without protective cover on top of the drive) operating altitude<= 1000 m without>= 1000 m with current derating 1 % per 100 m Contractual warranty Warranty18 months
User guideFormatSizeAdd to My DocumentsCADFormatSizeAdd to My Documentsprp.document.label.format zipSize 578.3 KBDate 11/13/07Instruction sheetFormatSizeAdd to My DocumentsEnd of Life InformationFormatSizeAdd to My Documents
- All Languages7
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.